How to Select Well site

 

Groundwater is a natural replenishable resource. It is an important source for various purposes, including drinking, irrigation and industrial, due to insufficient surface water supply and frequent failure of monsoon. Identification of groundwater zones depends upon many factors such as distribution of rainfall, runoff, grain size of soil, topographic features, type of landform, drainage conditions, lithological characteristics, land use practices, depth to groundwater level and environmental constraints, which are not uniform in any area. 



Therefore, the following guidelines are essential and can be applied locally or regionally for success of well site selection -

  • Low-lying areas are more favorable as compared to sloppy area and highlands for sinking wells, as groundwater flows in the direction of descending slope.
  • Vegetation flourishes where the groundwater is available at shallow depths. Thus, the occurrence of thick vegetation indicates large groundwater storage at shallow depth. However, the presence of vegetation like desert plants indicates the scarcity of groundwater at shallow depths, as they absorb water from the sub-surface and store it in their thick fleshy leaves and stems.
  • Areas comprising thick soil or alluvium cover and weathered, fractured, jointed, and faulted rocks indicate good storage of groundwater, as these support infiltration of groundwater recharge. However, fine-grained soils like clay cannot support infiltration of groundwater. Moreover, they cannot transmit water from one place to another and have saline groundwater due to stagnation. Coarse-grained soils transmit water and hence the water is potable. Bald rocky areas lack such favorable conditions as they do not permit infiltration of water. Thus, these rocks indicate paucity of groundwater. 
  • Surface water bodies like tanks, ponds, lakes, streams, reservoirs and rivers serve as sources of recharge to the nearby areas. Thus, if we sink wells in and around the areas of surface water bodies, the wells can yield sufficient water. 
  • The study of existing wells in the vicinity of the proposed well sites with respect to soil cover, rock types (hard rock or soft rock) and their structural conditions (fractures, joints, faults, etc.) depth to water table and well yield is essential to have a clear picture of the hydrogeological conditions of an area. 
  • Scanning of sub-surface hydrogeological conditions like depth of soil zone, weathered zone, fractured/jointed zone and unfractured zone from the ground surface is essential. From these surveys, it is possible to assess the depth of saturated zone and water quality (saline or non-saline). Such surveys should be conducted in summer to know the real depth of the saturated zone. This zone is generally deep in summer and shallow in the other seasons. If we conduct the surveys in seasons other than in summer, there could be decline or dry-up of water conditions in summer, as the shallow depth of saturated zone observed from the remaining seasons can decline. 
  • If two wells are situated close to each other in a more or less plain land, the supply of water can be greatly affected due to well-interference, when both the wells are pumped simultaneously, especially in summer. This is because, the water in a shallow well can get depleted or dried-up rapidly than the water in a deep well. Thus, it is important to maintain a distance of 150–300 m in alluvial areas and 75–150 m in rocky areas between two wells. 
  • The water level in any area can decline or dry-up in summer due to lack of infiltrating recharge. But, the depletion of water level can be rapid in the uplands than in low-lying areas of the same place due to heavy pumping of wells in the low-lying lands, which sometimes lead to drying of wells, irrespective of the distance of wells between them. These conditions can reach alarming levels, where the apartments are more due to over-exploitation. 
  • For large scale of well-sinking programme, integration of satellite data with hydrogeological data, can help in making rapid survey of an area.

Comments

Post a Comment

Popular posts from this blog

How to Choose Aggregate?

Image
  Aggregates Aggregates are inert granular materials such as sand, gravel, or crushed stone that, along with water and portland cement, are an essential ingredient in concrete. For a good concrete mix, aggregates need to be clean, hard, strong particles free of absorbed chemicals or coatings of clay and other fine materials that could cause the deterioration of concrete. Aggregates, which account for 60 to 75 percent of the total volume of concrete, are divided into two distinct categories--fine and coarse. Fine aggregates generally consist of natural sand or crushed stone with most particles passing through a 3/8-inch sieve. Coarse aggregates are any particles greater than 0.19 inch, but generally range between 3/8 and 1.5 inches in diameter. Gravels constitute the majority of coarse aggregate used in concrete with crushed stone making up most of the remainder. Natural gravel and sand are usually dug or dredged from a pit, river, lake, or seabed. Crushed aggregate is produce...
Read more

Properties of a good building stone

Image
  Properties of a good building stone 1. Crushing Strength: For a good structural stone, the crushing strength should be greater than 100 N/mm 3 . The approximate values of crushing strength of some of the stones are shown in table 2-1.   2. Appearance: The stones which are to be used for face work should be decent in appearance and they should be capable of preserving their colour uniformly for a long time. The colour of the stones for face work should be chosen by keeping in mind the general get up of the surrounding area. It is desirable to prefer light coloured stones as compared to dark coloured stones. 3. Durability: A good building stone should be durable. The various factors contributing to durability of a stone are its chemical composition, texture, resistance to atmospheric and other influences, location in structure, etc. Following are the important atmospheric agencies which affect the durability of a stone: (i) Alternate conditions of heat and co...
Read more

Mass timber construction

Image
Mass timber construction Mass timber construction, also known as timber or wood-based building construction, is an emerging construction trend that is gaining popularity due to its eco-friendliness, cost-effectiveness, and structural advantages. Mass timber construction is the use of large, solid wood panels or engineered wood products as a primary structural element for buildings. These panels are assembled using various methods to create a strong, durable, and sustainable structure. Mass timber construction can be seen as a solution to the increasing environmental concerns around the world, especially in urban areas, where the demand for sustainable and eco-friendly construction is rising. The benefits of mass timber construction include carbon sequestration, reduced construction time, and a lower carbon footprint. The use of wood products in construction also contributes to the growth of the timber industry and the local economy. The most common types of mass timber used in construc...
Read more